What is the difference between the three-jaw chuck and ...

Author: Melody Liu

Dec. 06, 2023

269

0

0

Tags: Hardware

Something went wrong. Wait a moment and try again.

8

Unit 3: Chucks

OBJECTIVE

After completing this unit, you should be able to:

• Describe different type chucks.

Chucks:

Some work pieces, because of their size and shape, cannot be held and machined between lathe centers. Lather chucks are used extensively for holding work for machining operations. The most commonly used lathe chucks are the three jaw universal, four jaw independent, and the collects chuck.

Three-jaw universal chuck:

Three-jaw universal chuck is used to hold round and hexagonal work. It grasps the work quickly and within a few hundredths of a millimeters or thousandths of an inch of accuracy, because the three jaws move simultaneously when adjusted by the chuck wrench. This simultaneous motion is cause by a scroll plate into which all here jaws fit. Three jaws chucks are made in various sizes from 1/8-16 inch in diameter. They are usually provided with two sets of jaws, one for outside chucking and the other for inside chucking.

Figure 1: Three-jaw universal chuck

Four-jaw independent chuck:

This four- jaw independent chuck has four jaws; each of which can be adjusted independently by a chance wrench. They are used to held wound, square, hexagonal, and irregular-shaped workpieces. The jaws can be reversed to hold work by the inside diameter.

Figure 2: Four-jaw independent chuck

Collect chuck:

The collect chuck is the most accurate chuck and is used for high precision work and small tools. Spring collects are available to hold round, square, or hexagon shaped workpieces. A adaptor is filled into the taper of the headstock spindle, and a hollow draw bar having an internal thread is instead in the opposite end of the headstock spindled. As the hand wheel and draw bar is revolved, it draws the collet into the tapered adaptor, causing the collet to tighten on the workpieces.

Suggested reading:
Hardware
What is profiling steel?
Optimal Pressure for Torch Cutting: A Comprehensive Guide

Figure 3: Collect chuck

The Jacob collect chuck has a wider range the spring collect chuck. Instead of a draw bar, it incorporates an impact-tightening hand wheel to close the collect on the workpiece. A set of II rubber flex collects, each capable of a range of almost 1/8 in, makes it possible to hold a wide range of work diameter. When the hand wheel is turned clockwise, the rubber flex collect is forced into a taper, causing it to tighten on the workpiece. When the hand wheel is turned counterclockwise, the collect opens and releases the workpiece.

Magnetic chucks:

A magnetic chucks are used to hold iron or steel parts that are too thin, or that may be damaged if held in a conventional chuck. These chucks are fitted to an adaptor mounted on the headstock spindle. Work id held lightly for aligning purposes by turning the chuck wrench approximately ¼. After the work has been turned

Faceplates:

A faceplates are used to hold work that is too large or of such a shape that it cannot be held in a chuck or between centers. Faceplates are equipped with several slots to permit the use of bolts to secure the work, so that the axis of the workpiece may be aligned with the lathe centers. When work is mounted off – center, a counterbalance should be fastened to the faceplate to prevent imbalance and the resultant vibrations when the lathe is in operation.

UNIT TEST

1. What are the most commonly used lathe chucks? Name three.

2. Describe three-jaw universal chuck.

3. Describe four-jaw universal chuck.

4. Describe Collect chuck.

5. Describe Jacobs collect chuck chuck.

6. Describe Magnetic chucks chuck.

7. Describe Faceplates

What is the difference between the three-jaw chuck and ...

Unit 3: Chucks – Manufacturing Processes 4-5

Comments

Please Join Us to post.

0

0/2000

Guest Posts

If you are interested in sending in a Guest Blogger Submission,welcome to write for us.

Your Name: (required)

Your Email: (required)

Subject:

Your Message: (required)

0/2000